Hp Laptop Battery Replacement, Not Charging

2 min read

Buy a new HP laptop battery. Before you think about opening your computer and starting this process, you need to order a new battery first.
Create a battery report in Windows. Before you perform an HP battery replacement, you should know how well your battery is performing.
Disconnect your laptop from power. This is the easiest step in the process, How long will it last, if it is not durable then you have to replace the new one.

Create a battery report in Windows

Before you perform an HP battery replacement, you should know how well your battery is performing. Windows has made this simple with its battery report. Here’s how to create a report:

  • Click in the lower left corner of your screen to display the Command Prompt
  • Type “powercgg / batteryreport” and press “Enter”
  •  A report on the status of the battery will be saved
  • Click your Users folder to find and review battery reports

The report provides an overview of past battery performance and an overview of the previous three charge cycles. You’ll want to look at Design Capacity vs. Full Charging Capacity to determine if it’s worth replacing the battery.

Disconnect your laptop from power

This is the easiest step in the process, but it needs to be repeated. In addition to shutting down your laptop completely, you also want to make sure that you have disconnected it from the power source.

Remove the back panel of your laptop with a screwdriver

Most HP laptops require the removal of the rear panel for battery replacement. This means you may have to buy a Phillips-head screwdriver #0 or a laptop starter kit, both of which are inexpensive and can make the process of installing a new battery simpler.

There may be some rubber legs on the back panel that you have to remove before you can access the battery, but this depends on your HP laptop model. Use a plastic opener to pry through the rubber, allowing you to remove the screws that hold the body of the laptop.

Use a Phillips screwdriver to loosen the screws on the rear panel and then carefully remove the back cover of your laptop. This may require you to use a plastic tool again to loosen the tip. It is usually easier to start from an angle and carefully remove the panel, but be sure to be careful not to damage the components inside.

Remove your laptop battery

Use your Phillips screwdriver to remove the screws that hold your battery in place inside the body of the computer. Once loosened, you must disconnect the cable connecting the battery to your system.

Be careful when doing this because these parts are sensitive and you may cause problems in the future if you damage them. Also, be sure to remove the battery completely from your device. Remove the new battery from the package and make sure it is clean of plastic.

Connect your new battery to the body of your laptop

At this stage, you can start the process of connecting a new battery. After you insert the new battery, you need to reverse the steps you just completed to get your computer up and running again.

  • Connect the cable on your computer to the new battery carefully
  • Plug your battery back into the body of your device
  • Make sure the battery is properly installed, but not too tight as it may damage some components

Reattach the rear panel

Align the back cover with the rest of your laptop before using a Phillips screwdriver to reattach the cover. Again, you should be careful not to make items too tight or loose, as one of them can damage your device. Replace the rubber footing on the bottom of your laptop if your computer has one.

Confirm performance with new battery reports

Once everything is lined up and reunited, connect your computer to a power source. After a few minutes of charging, turn on your laptop to make sure everything starts correctly. If your laptop seems to be functioning properly, you’ll want to do another battery report to see what your Design Capacity is and if everything looks the way you expect.

Hp Laptop Battery Not Charging

Why is My Laptop Battery Not Charging? there are several factors beterai not charging that may be caused by beterai already damaged, or the driver must be updated.

  • From the Start menu, search for Device Manager
  • Select Battery and identify the driver for your battery
  • Right-click the driver and select Update Driver
  • If the driver requires a newer version, it will be updated, and you can restart your computer
  • If you didn’t get the charging symbol above the battery icon on your desktop toolbar, but now it appears, this might be the case.


Leave a Reply

Your email address will not be published. Required fields are marked *